

An autumn checklist for a London property
- Consider branches and seasonal debris together
- Plan around the building, not just the calendar
- Prepare for cold weather while access is straightforward
Choose an autumn order that suits your building
Use the transition into wetter weather to plan work on the roofline, trees, glazing and the paths you use most often.
For a property below large deciduous trees, record when the heaviest leaf fall tends to reach the gutter. A front path that stays wet may need attention earlier than a lightly used rear patio. Arrange any tree assessment first if branches are touching the roof. Schedule glazing and surface work after the jobs likely to drop material onto those areas.

What to look for
Consider branches and seasonal debris together
Overhanging branches can drop material into a gutter, cast shade over paths and sometimes touch the roofline. These effects call for different responses. Clearing a gutter restores an open route for water, while work on a branch changes how it interacts with the building. An overhanging branch should be assessed in its setting, particularly near a boundary, a glass roof or other property. Do not assume the tree needs heavy pruning just because leaves are collecting below it. Describe which branches cause concern and check who can authorise any work before arranging it.
Plan around the building, not just the calendar
Roof pitch, nearby trees and the amount of moss on the tiles all affect how quickly material accumulates. Two buildings on the same road may therefore need different intervals. A gutter below a deciduous tree may collect most of its leaves over a few weeks, while one below a mossy roof can receive debris after successive wet spells. Note when the gutter last overflowed and what was happening around the property at the time. That record is a better starting point for a maintenance interval than assuming every roofline needs the same visit at the same time of year.
Prepare for cold weather while access is straightforward
Autumn checks are easier before paths become slippery and access is interrupted by frost or storms. Look for places where water repeatedly pools, especially by steps, side passages or entrances. Follow the visible route from roofline to ground rather than treating the gutter, downpipe and paving as separate concerns. If a path stays wet because an outlet above it overflows, cleaning the path addresses a symptom while the discharge continues. Check what can be seen safely from ground level and arrange an assessment before the affected area becomes harder to reach.
Let the trees set part of the timetable
If a particular tree drops most of its leaves in a short period, make a note of that period rather than committing every roofline to the same date. The front and rear of a property may respond differently to the same season. Where branches touch the roof, discuss the tree and gutter as separate jobs so both the source of contact and the accumulated debris are considered.
A practical check before booking
Consider branches and seasonal debris together
Start with the first visible sign and note where on the property it appears.
Choose an autumn order that suits your building
Use the example above to decide what details are worth recording for your own property.
Choose the next assessment
Use the table to decide what to describe when you speak to the relevant service.
| Observe | Record | Discuss |
|---|---|---|
| Position | The elevation, surface or part of the system affected | Which area needs assessment first |
| Timing | When the problem appears and what makes it worse | What can be checked during a visit |
| Access | How the area can be reached and who can open it | Which parts are accessible and what may need separate work |
The outlet is a separate checkpoint
The outlet is where the open gutter connects to the downpipe. A blockage there can make the channel fill even when most of the run is free of leaves. The visible sign can be a concentrated spill at the corner or a hopper that fills without discharging. The point that overflows is useful to report, but the obstruction might sit slightly upstream or within an accessible bend. If a pipe joins a water butt, note the position of its diverter. It helps to distinguish the parts of the system that are visible from sections that disappear behind a wall or beneath the ground.
Follow the downpipe to ground level
Rainwater has another journey after leaving the roof. Some pipes terminate above an open gully, while others feed a water butt or go directly into a drain. A gully that is already full can make a downpipe problem look like a roofline blockage. Paving that slopes towards a doorway can also carry water from another part of the property. From a safe position, note whether water backs up at ground level, escapes from a pipe connection or never reaches the outlet at all. These are different observations, and a gutter visit may not resolve a problem downstream of the rainwater pipe.
Match outdoor cleaning to the surface
A paved path, a timber deck and a stone step can all become green in shade, but they do not respond the same way to cleaning. Start by identifying the material and looking for loose joints, soft spots or failing finishes. The way water leaves the area matters as much as the way it is applied. If the surface slopes towards a doorway, inspect the channel or threshold from ground level and note whether water already pools. Surface washing may help with algae and grime, while worn coatings, loose material or failed drainage can call for separate work.
Look at glazing after work above it
Roofline and garden work can send dirt onto panes that were clean a few days earlier. If several jobs are planned, consider which will disturb material over the others. A shopfront beneath a leaking canopy may keep collecting dirty streaks until the source above is addressed. A lower window beside a driveway may be affected by spray from surface washing. Identify the glass that needs attention and describe any stained frames, sealed units or residue left by building work separately. This helps distinguish routine exterior cleaning from a mark that requires a different assessment.
Plan what happens next
Start where visitors first encounter the building
An entrance can look tired because several small problems coincide: a streak under a downpipe, green growth on a shaded step and dull glazing behind a canopy. Give each a priority based on what affects access and what is likely to get dirty again. A dripping fitting can undo a surface clean, while an obstructed step or path may matter before the appearance of the upper windows. Choose a sequence that removes the source first and finishes with the surfaces that would otherwise be marked during the earlier work.
Look at how the roofline can be reached
Properties with similar roof heights can require different access. An unobstructed front elevation may be approachable from ground level, while a rear run of the same house sits above a glass roof or beyond a shared passage. A pole needs space at its base and a usable angle to the gutter. A path along the side of a building may be too narrow for one part of the run even when there is room elsewhere. If you are booking a visit, explain how to reach the back, whether there are gates or steps, and what sits directly below the affected gutter.
Make the first enquiry specific
Give the full postcode, property type and affected elevation. For gutters, say whether the problem is at a joint, outlet, hopper or the wall below. For exterior work, describe the material or tree and mention access restrictions. A wider photo from a safe position is useful because it shows where the work sits in relation to doors, gates and paths. A close-up alone may not show the height or approach. For shared premises, include the person who can agree access and identify the section to be worked on. Avoid assuming that all parts of a property will be included by default.
Do the work in an order that lasts
A path may need attention early if it is a route to the entrance. Glazing and patio furniture can often wait until roofline or tree work is complete. Make separate notes for a leak, a dirty surface and a damaged fitting, even if all three are near the same door. That makes it easier to choose which service to contact and which work can be bundled.